Explore Now

What're your thoughts with regards to Installing A Bathtub?

Mounting a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, as well as often, tiling skills. Changing an old tub with a new one is also a reasonably tough job. If the old tub is conveniently obtainable, the job can move quickly; if you need to open a wall surface to eliminate the old tub and also place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the new one. Make sure you have actually certified yourself for the job and fit trying it. As opposed to employing a professional to take over a halfway-completed project, it is better to take into consideration utilizing one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your restroom if you have actually already bought a new bathtub as well as don't require to alter the arrangement of your previous supply of water pipes.
Your devices as well as product list ought to consist of the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Preparing for the Installment

First of all, the supporting framework provided with the bath needs to be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final setting.

Removing Old Touches

If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth prepared for the staying water that will come from the pipes. When the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.

Installing the Bathtub

Using the two wood boards under its feet, put the tub in the called for placement. The wood boards are practical in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bath tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the outermost flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's user's manual. Tiling and also sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will settle it right into its final position.

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in location between the faucet and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet ports. The former kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

Tiling Around the Bathtub

In the location where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a rigid seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can break relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily readily available on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof sticky as well as cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I am just very eager about Installing A Bathtub and I hope you enjoyed reading the entire blog entry. So long as you enjoyed reading our post please make sure you remember to pass it around. Thanks for going through it.

Additional Information